应力对La0.83Sr0.17MnO3薄膜输运性能的影响

采用溶胶-凝胶方法在Si(111)上制备了LSMO(x=0.17)薄膜.研究了块体材料和不同厚度薄膜R -T曲线、红外光谱和X射线衍射.结果表明，LSMO薄膜属于正交晶体结构，薄膜取向与膜厚度 有关，当膜厚度为450nm或680nm时，主要取向〈200〉，而膜厚度为900nm时取向为〈020〉 ：根据离子对相互作用能和谐振子模型，得到了红外吸收与Mn—O—Mn键长和键角关系式，6 00cm^-1附近红外吸收与晶格常数b的变化有关；块体与薄膜的金属—绝缘体转变 温度(T_MI)存在较大差别，薄膜转变温度显著低于块体，并与厚度有一定关系. 认为是LSMO薄膜中的应力诱导了晶格常数变化，引起键角改变及JT效应是转变温度变化的主 要原因. 关键词： 单晶硅 晶格常数 金属—绝缘体转变温度 应力诱导     

金属─助剂相互作用对SiO_2载铑催化剂化学吸附的影响Ⅰ．Rh_2－V／SiO_2催化剂

本文用化学吸附、原位ＩＲ、和ＸＰＳ考察了钒助剂对Ｒｈ２／ＳｉＯ２催化剂的Ｈ２和ＣＯ化学吸附的影响．结果表明，１）ＣＯ吸附在ＲｈＩ、ＲｈⅡ和ＲｈⅢ中心上分别产生孪生、线式和桥式ＣＯ表面吸附物种．２）Ｈ２主要解离吸附在ＲｈⅡ和ＲｈⅢ中心上，但ＣＯ能优先吸附；ＲｈＩ中心对Ｈ２的化学吸附能力弱，但Ｈ２和ＣＯ能共吸附在ＲｈＩ中心上形成表面羰基氢化物．３）Ｒｈ２－Ｖ／ＳｉＯ２催化剂在５７３Ｋ还原后，铑与钒助剂的强相互作用主要发生在ＲｈⅡ和ＲｈⅢ与钒助剂之间，Ｈ２吸附比ＣＯ吸附受到更强烈的抑制．用覆盖模型可以较好地解释钒助剂对Ｒｈ２／ＳｉＯ２催化剂的Ｈ２和ＣＯ化学吸附的影响．     

磷酸三丁酯从硝酸介质中萃取铀（Ⅵ）的动力学研究

用上升单液滴法和恒界面池法研究了磷酸三丁酯-环己烷从硝酸介质中萃取铀(Ⅵ)的动力学。萃取过程为扩散控制,得到了在扩散控制下影响萃取速率的一些规律。     

电沉积富铁Fe-Ni合金箔工艺的研究

对硫酸盐-氯化物电解液中电沉积富铁Fe-Ni合金箔的工艺进行了研究,讨论了电解液组成、电流密度、温度及pH值等因素与合金箔组成之间的相互关系,得到了制备富铁合金箔的最佳镀液组成及工艺条件,并通过实验确定在阴阳极比为1:2时,镍铁联合阳极配比为1.5:1.通过扫描电镜,能谱和X-衍射对富铁Fe-Ni合金箔的形貌及结构进行分析表明合金箔晶粒细致,尺寸均匀,结构紧密,表面光滑平整,无孔洞和裂纹,晶粒结构为(111),(200),(311)及(222)织构,并表现为较强的(111)择优取向.     

穿过液膜的自发电势振荡

An artificial membrane consisting of pricramic acid in nitrobenzene was used as an oil phase imposed between two aqueous phases. The right one contained trimethyl-slearylammonium chloride and aicohol; and the left contained sucrose solution (or H_2O). We found that this system exhibited rhythmic oscillation of electrical potential. The amplitude of the oscillations was between 20—150 mV. The oscillations were observed even when ethyl alcohol was absent in the aqueous of trimethylslearylammonium Chloride, and the increase in amplitude of oscillation with time was found to be less in the presence of sucrose. Some of the expremental results have been explained.     

SUPER TOUGH GELS WITH A DOUBLE NETWORK STRUCTURE

 Living tissues work with fantastic functions in soft and wet gel-like state. Thus, hydrogels have attracted much attention as excellent soft & wet materials, suitable for making artificial organs for medical treatments.However, conventional hydrogels are mechanically too weak for practical uses. We have created double network (DN) hydrogels with extremely high mechanical strength in order to overcome this problem. DN gels are interpenetrating network (IPN) hydrogels consisting of rigid polyelectrolyte and soft neutral polymer. Their excellent mechanical properties cannot be explained by the standard fracture theories. In this paper, we discuss about the toughening mechanism of DN gels in accordance with their characteristic behavior, such as large hysteresis and necking phenomenon. We also describe the results on tissue engineering application of DN gels.     

Synthesis of monodisperse poly(chloromethylstyrene-co-divinylbenzene) beads and their application in separation of biopolymers

The monodisperse, porous poly(chloromethylstyrene-co-divinylbenzene) beads of 7.9 microm were prepared by a single-step swelling and polymerization method. The seed particles prepared by dispersion polymerization exhibited good absorption of the monomer phase. Based on this media, a weak cation-exchange (WCX) stationary phase for HPLC was synthesized by a new chemically modified method. The prepared resin has advantages of biopolymer separation, high column efficiency, low column backpressure, high protein mass recovery, and good resolution for proteins. The dynamic protein-loading capacity of the synthesized WCX packings was 18.2 mg/g. Five proteins were separated in 3.0 min using the synthesized WCX stationary phase. The experimental results show that the obtained WCX resin has very weak hydrophobicity. The WCX resin was also used for the rapid separation and purification of lysozyme from egg white in 5.0 min with only one step. The purity and specific bioactivity of the purified lysozyme were found to be more than 93% and 70 245 U/mg, respectively.     

助剂对Cu/Cr催化剂上甲醇部分氧化制氢的活性影响

曾研究了Cu/Cr二元催化剂上甲醇部分氧化制氢的反应，发现当Cu/Cr比为6：4时，催化剂的Cu^0比表面积最大，呈现出较好的活性。在Cu/Cr（6：4）催化剂中添加Fe,Zn,Al等8种助剂，考察其对甲醇部分氧化制氢催化性能的影响，并着重研究了Zn助剂的作用。实验结果表明，Zn的引入，有利于催化剂活性的提高。当Zn含量为10％时，催化剂活性最好。XRD表征结果表明，Cu/Cr催化剂的失活与其表面上的Cu物种烧结有关，Zn的引入可明显增强Cu/Cr（6：4）催化剂的热稳定性，提高其寿命。